To prepare students for entry level or additional education in the business industry.
Benchmark 1
Materials Management
Indicator 1
The student will describe why materials are chosen on the basis of their properties.
Indicator 2
The student will describe how technological systems process resources from one form to another to meet human wants and needs.
Indicator 3
The student will document the names and uses of tools and equipment that help fulfill basic needs during a selected day.
Indicator 4
The student will test material properties (hardness, conductivity, relection, etc.)
Indicator 5
The student will list and describe alternatives to fossil fuels.
Indicator 6
The student will describe the technological process used to recycle waste material.
Indicator 7
The student will define and explain the concept of ergonomics.
Benchmark 2
Construction Management - Estimate Materials
Indicator 1
The student will estimate rough framing materials.
Indicator 2
The student will estimate roofing materials.
Indicator 3
The student will estimate windows.
Indicator 4
The student will estimate doors and jambs.
Indicator 5
The student will estimate siding.
Indicator 6
The student will estimate concrete.
Benchmark 3
Construction Management - Preparing Building Site
Indicator 1
The student will set up and use builders level.
Indicator 2
The student will layout the building site.
Benchmark 4
Construction Management - Installing Rough Framing
Indicator 1
The student will stack lumber.
Indicator 2
The student will install sill plate.
Indicator 3
The student will frame a wall.
Indicator 4
The student will align and brace a wall.
Indicator 5
The student will construct a corner post.
Indicator 6
The student will frame a floor opening.
Indicator 7
The student will frame a window opening.
Indicator 8
The student will frame a built-up stringer.
Indicator 9
The student will install floor joists.
Indicator 10
The student will install exterior wall sheathing.
Indicator 11
The student will install roof sheathing.
Benchmark 5
Construction Management - Installing Roof Components
Indicator 1
The student will install roofing felt.
Indicator 2
The student will install composite strip shingles.
Indicator 3
The student will install composite shingles on ridge cap.
Indicator 4
The student will install composite shingles around roof opening.
Indicator 5
The student will install roof vent.
Benchmark 6
Construction Management - Installing Exterior Finishes
Indicator 1
The student will apply composition siding.
Indicator 2
The student will install corner board for masonite siding.
Indicator 3
The student will install fascia.
Indicator 4
The student will install vinyl siding.
Indicator 5
The student will install drip cap.
Indicator 6
The student will install prehung exterior door.
Benchmark 7
Construction Management - Installing Interior Finishes
Indicator 1
The student will install batt insulation.
Indicator 2
The student will install baseboards.
Indicator 3
The student will hang drywall.
Indicator 4
The student will install a prehung door unit.
Indicator 5
The student will install a cylinder lockset.
Indicator 6
The student will cope moulding.
Indicator 7
The student will drive screws.
Indicator 8
The student will drive and set nails.
Benchmark 8
Construction Management - Finish Surfaces
Indicator 1
The student will stain and surface.
Indicator 2
The student will brush on and clean top coat.
Indicator 3
The student will prepare surfaces.
Indicator 4
The student will apply paint.
Benchmark 9
Construction Management - Power Tools
Indicator 1
The student will identify power tools.
Indicator 2
The student will select the correct power tool according to job.
Indicator 3
The student will demonstrate safe and proper use of power tools.
Indicator 4
The student will apply safety rules and procedures.
Indicator 5
The student will operate a circular saw. a. Remove and replace blades and make adjustments. b. Make straight cuts to layout lines.
Indicator 6
The student will operate a saber saw. a. Remove and replace blade and make adjustments.
Indicator 7
The student will operate a drill. a. Remove and replace drill bits. b. Drill and bore holes through stock. c. Drill and bore holes to specified depth. d. Drill pilot hole.
Indicator 8
The student will operate a power screwdriver. a. Remove and replace bits and make adjustments. b. Drive screws.
Indicator 9
The student will operate a sander. a. Remove and replace abrasive and make adjustments. b. Sand a surface with a finishing sander.
Indicator 10
The student will operate a tablesaw. a. Inspect and clean a table saw. b. Remove and replace table saw blades. c. Lay out and make a rip cut.
Indicator 11
The student will operate a drill and drill press. a. Inspect and clean drill and drill press. b. Remove and replace cutting tool and adjust table and stops. c. Drill and bore holes in stock.
Indicator 12
The student will operate a power miter saw. a. Remove and replace blade. b. Crosscut to length. c. Cut miters.
USD
250 Home Page
General info:
Vicki Horton
Tech info:
Rick Duling
Webmaster:
Noah Grotheer
©
Pittsburg Public Schools